your trusted source for automotive paint and refinishing
Shopping Cart$0.00
0
PROUDLY CANADIAN
FREE GROUND SHIPPING ON ORDERS OVER $450
Sale!
NORTON 70735 Foam Masking Tape 13mm X 50m
Easy-to-use, time-saving products to mask door jambs and other apertures like hood and deck lid openings that need to be sealed during the painting process. The Premium Foam Masking Tape features a semi-split design and offset adhesive to ensure a soft paint edge.
Used in wet sanding, rough featheredging. Could be used for final sanding of plastic filler and putty. Most flexible backing with more consistent scratch pattern make this 3Ms best wet sanding product.
BETASEAL™ U-418 speeds installations – eliminates the glass priming step. BETASEAL U-418 provides primerlessto-glass convenience with excellent workability, sag resistance and convenient drive-away times. BETASEAL U-418 is easy to use and does not require heating. It is available in cartridges. Product benefits include: Primerless to auto glass FMVSS crash proven Meets all long-term durability requirements Ready to use – no heating required Applications Structurally bonded or direct glazed automotive glass, such as windshields, backlites, quarter glass and other stationary glass Other uses such as attaching hardware to glass and backfilling to install reveal moldings or other trim BETASEAL U-418 Quick Cure Auto Glass Urethane Adhesive Application details See vehicle manufacturer’s recommendations for additional details. Do not use any other manufacturers’ primers, cleaners or other chemicals in conjunction with any BETASEAL adhesive system Apply at temperatures of 40˚F (4.4˚C) and warmer Physical properties Appearance – black, smooth paste Solids content – 94% Flash point – > 110˚F (43˚C) Weight per volume – 10.1 lbs/gal Specific gravity – 1.2 Sag – none Odor – minimal Tack-free time – 25 minutes after application at 72˚F (22˚C) and 50% RH Working time – 15 minutes at 72˚F (22˚C) and 50% RH Full cure – less than 24 hours at 72˚F (22˚C) and 50% RH
Patterned, precise mineral structures give Trizact™ abrasives the combination of fast cut and consistent finish every time. Use P1000 foam blending discs for scuff sanding blend panels prior to painting. Use P1500 clearcoat sanding discs for leveling dust nibs and sanding of mismatched orange peel. Finally, use P3000 foam disc for removing P1200-P1500 grade sand scratches prior to use of 3M™ Perfect-It™ polishing system. Foam disc used in a spot repair system for removing sanding scratches before using rubbing compound.
NIOSH approved against certain organic vapors, acid gases, ammonia methylamine, formaldehyde with P100 particulate filter
Bayonet compatibility allows use with many 3M™ Half and Full Facepiece Designs
Wide range of applications reduces inventory needs
To establish cartridge replacement frequency visit: 3M.com/ServiceLifeSoftware
Details
The 3M™ Multi-Gas/Vapour Cartridge/Filter 60926 is NIOSH approved against certain organic vapours, acid gasses and particulates. Use with 3M™ Half and Full Facepiece Respirators 6000, 7000 and FF-400 Series with bayonet filter holders.
3M™ Multi-Gas/Vapour Cartridge/Filter 60926 P100 may be used for respiratory protection from certain organic vapours, chlorine, hydrogen chloride, sulfur dioxide, chlorine dioxide, hydrogen sulfide, ammonia, methylamine, formaldehyde, or hydrogen fluoride, and non-oil and oil particulate concentrations up to 10 times the Permissible Exposure Limit (PEL) with half facepieces or 50 times PEL with quantitatively fit tested full facepiece masks. This cartridge/filter is not for use in environments that are Immediately Dangerous to Life or Health (IDLH). Recommended applications for the cartridge/filter include petrochemical and chemical processing. Inventory needs and training requirements for safety equipment are reduced because this respirator cartridge selection works for many different applications. This cartridge/filter is commonly used in the following industries: utilities, pharmaceuticals, mining, oil and gas, and primary metals.
NIOSH approved against certain organic vapors, acid gases, ammonia methylamine, formaldehyde with P100 particulate filter
Bayonet compatibility allows use with many 3M™ Half and Full Facepiece Designs
Wide range of applications reduces inventory needs
To establish cartridge replacement frequency visit: 3M.com/ServiceLifeSoftware
ANDREAE Standard Filters are used in the exhaust of paint booths for over-spray collection.
The front V-shaped wall prevents over-spray bounce back and migration. The deeper V-shape of the back wall is the paint holding pocket.
The exhaust holes are misaligned to divert the paint laden airflow to the holding pocket, where the paint is captured, while maintaining a constant flow during the loading phase.
PRODUCT OVERVIEW:
Lasts 3 x 5 times longer than poly, fiberglass or mesh media
Captures any wet solid or liquid particles
Standard & high efficiency options
V shape wall prevents over spray and bounce back migration
Foam
