Be the first to review “3M 2097
PARTICULATE FILTER, 2097, P100” Cancel reply
PARTICULATE FILTER, 2097, P100” Cancel reply
The 3M™ Particulate Filter 2097 is NIOSH approved for environments containing certain oil and non-oil based particles. 3M recommended for nuisance level organic vapour relief and for ozone protection up to 10X OSHA PEL.
3M™ Particulate Filter 2097 with nuisance level organic vapour relief helps provide respiratory protection against exposure to lead, asbestos, cadmium, arsenic, and MDA. The filter is effective for concentrations up to 10 times the Permissible Exposure Limit (PEL) with half facepieces, or 50 times PEL with quantitatively fit tested full facepieces. This filter helps protect against a wide range of oil and non-oil based particulate contaminants. The filter also offers nuisance level odour relief from organic vapours that are below the PEL. Nuisance level refers to concentrations not exceeding OSHA PEL or other applicable government exposure limits, whichever is lower. Do not use for respiratory protection against organic vapours or in environments that are Immediately Dangerous to Life or Health (IDLH). The 2097 is commonly used for welding, brazing, torch cutting, metal pouring and soldering. Inventory needs and training requirements of safety equipment are reduced because this filter works for many different applications. The filter is both flame and water resistant. This filter is commonly used in the following industries: agriculture, construction, general manufacturing, pharmaceuticals, primary metals.
$12.18
In StockMSV-21 2.1 VOC Urethane Clearcoat is a low VOC clear designed for general refinish work. MSV-21 is an easy to apply medium solids clear. MSV-21 2.1
VOC Urethane Clearcoat is versatile and delivers a productive, high gloss finish.
Hardener
• MHV-21F 2.1 VOC Fast Hardener
• MHV-21N 2.1 VOC Normal Hardener
• MHV-21S 2.1 VOC Slow Hardener
*Hardener must be ordered separately*
The Scotch-Brite™ 3M™ Roloc™ + clean and strip disc aggressively removes paint and rust from seams, door jambs, drip moldings, pinchwelds and other difficult-to-reach areas. Its three-dimensional abrasive web conforms to most work pieces, offering a safer process than with wire bristle tools.
Make tough jobs easier. Scotch-Brite™ Discs can help you achieve a burr-free, paintable finish in fewer steps without damaging the base material. The non-woven, open-web, durable construction helps to resist loading and greatly increases the life of the disc. As a result, you will not have to change it as often.
A translucent linered tape with a rigid band to lift pliable molding to allow paint coverage under the molding, thus eliminating a visible paint edge.
A translucent linered tape with a rigid band to lift pliable molding to allow paint coverage under the molding, thus eliminating a visible paint edge
Taff-Guard two layer intake panels are constructed using two synthetic layers of media sealed over a metal wire frame. The first layer, dry and white, acts as a pre-filter to remove the medium and large particles. The second layer, green with an adhesive, removes and retains the smaller particles.
Typically, this intake filter is installed in the paint booth doors and/or ceilings. However, these paint booth filters can be used in any standard HVAC application as well.
100% synthetic material with tack layer to trap dirt particles
Low resistance to air flow which results in minimal energy costs
Will not absorb moisture or humidity
Prefilter for multistage units
Paint Booth, Spray Booth and Auto body filter
Standard HVAC applications
Formulated for fast work, dries rapidely and is easy to sand. It’s creamy texture and good spreading allows easy repair of large areas. It may be applied on steel, electrozinc-coated, galvanized, aluminum or polyester surfaces.
Reviews
There are no reviews yet.